// Güvenlik

Patch released for a vulnerability in Zyxel GS1900 switches that allows command execution from within the network

The stack-based buffer overflow vulnerability in Zyxel's GS1900 series switches can allow an unauthenticated attacker on the network to execute operating system commands on the device. The vulnerability has been added to CISA's exploited vulnerabilities list, and patches are available.

A security vulnerability in Zyxel’s GS1900 series smart managed switches was added to CISA’s Known Exploited Vulnerabilities (KEV) list on September 21, 2026. The vulnerability, registered as CVE-2026-7273, is described as a stack-based buffer overflow (CWE-121) in the CGI program of the device firmware. Zyxel had released fixed firmware in its June 16, 2026 advisory.

Why the vulnerability is dangerous

The most critical aspect of the vulnerability is that no username or password is required to exploit it. An unauthenticated attacker on the local network (LAN) can trigger the buffer overflow with a specially crafted HTTP request and execute operating system commands on the device. NVD’s CVSS 3.1 assessment gives it a score of 8.8, “high”: the attack vector is adjacent network (AV:A), complexity is low, and no privileges or user interaction are required.

The phrase “adjacent network” matters here. Even if the device is not exposed to the internet, an attack is possible through another device connected to the same network. In other words, a laptop connected to a guest Wi-Fi network at the office or home, a compromised smart device, or any device that can reach the management interface may be enough to attack the switch. The fact that the device sits at the center of the network also increases the risk: if the switch is compromised, it can be used to monitor and redirect traffic on the network.

Affected models and patch versions

Zyxel released patches for nine models within its support period. On affected devices, versions 2.90(xxx.1)C0 and earlier are affected by the vulnerability, and the fix arrives in 2.90(xxx.2)C0 versions:

  • GS1900-8 → 2.90(AAHH.2)C0
  • GS1900-8HP → 2.90(AAHI.2)C0
  • GS1900-16 → 2.90(AAHJ.2)C0
  • GS1900-24 → 2.90(AAHL.2)C0
  • GS1900-24E → 2.90(AAHK.2)C0
  • GS1900-24EP → 2.90(ABTO.2)C0
  • GS1900-24HPv2 → 2.90(ABTP.2)C0
  • GS1900-48 → 2.90(AAHN.2)C0
  • GS1900-48HPv2 → 2.90(ABTQ.2)C0

Zyxel states that current products not included in the advisory are not affected by this vulnerability. So no additional action is needed for models other than GS1900 and new products not on the list.

What to do

Because the vulnerability has entered the CISA list, U.S. federal agencies must apply the patch or disable the product by September 24, 2026. Even if you don’t have a corporate obligation, the deadline is a good indicator of urgency.

The first thing to do is check the software version from the device’s management interface and install the relevant 2.90(xxx.2)C0 file from Zyxel’s support page. Until the update is applied, precautions you can take include closing the switch management interface to the internet, keeping management traffic on a separate VLAN, and disabling unused remote management services. These measures narrow the source of an attack but do not close the vulnerability; the real solution is a firmware update.

If you use a GS1900 series switch in a home or small office network and the device hasn’t been updated in more than two years, this vulnerability is reason enough to update. Network equipment often remains in the “set it and forget it” category; yet these days such devices are among attackers’ first targets.

Source: CISA KEV · NVD

// JOIN THE CONVERSATION

Share your experience

Bir sorunun, farklı bir çözümün veya eklemek istediğin bir notun var mı? Giriş yapmadan da yazabilirsin.

// KEEP READING

One more note.

All posts ↗︎